Gas Burners - Common Causes for Slow or No Ignition, Burners Clicking. Surface burners are often slow to light or will not light at all because the burner or burners are wet or dirty, the electrode is not seated properly, or because the burner head and cap are not matched up properly. Check the following if the unit has power but is not lighting. I need a replacement igniter, part # 72242500, for my Miele KM326G (gas) stove top. The part number is what I just got from a Miele corporate service rep on the phone. To double check and verify that. Ignition Problems The pilot flame may fail to ignite the oven burner if it’s poorly adjusted or if the tubes running from the pilot flame to the burners are blocked. The electric igniter, on the other hand, has two principal functions: To open the valve.

  1. Miele Gas Cooktop Igniter Problems Chart
  2. Miele Gas Cooktop Igniter Problems Pictures
  3. Miele Gas Cooktop Ignition Problems
  4. Miele Gas Cooktop Igniter Problems
1Gas stove igniter won’t spark

A gas range will always make a clicking noise whenever you turn on the surface burner knob after which the burner will light. The noise comes from an electric igniter that sparks the burner and stops when the burner lights at least after clicking 3 times. If it doesn’t ignite, then there is a problem somewhere that needs to be addressed by a range repairman.

Gas stove igniter won’t spark

Cooktop

The following are common problems why a gas range igniter won’t light and how to repair them.

Some things to check when your gas stove not clicking or lighting:

Electric Stove Burners Not Working – Food Debris And Grease

Most gas burners have a problem lighting because of food debris or grease that blocks normal flow of gas.
Invite your residential gas range expert to your house for inspection of the faulty burner. First, the grate on top of the burner and the burner base will be removed. The burner base will then be soaked in warm water or vinegar and scrubbed with a stiff brush to remove food particles. Surrounding areas will also need to be cleaned with soapy warm water to remove grease.

Miele

Food clogged in the burner holes will need to be removed with a needle, paper clip or metal pin. Never use a tooth pick to remove food debris in the small holes as it can break off and get lodged inside the holes. Next, the burner and grill should be replaced for the burner to be lit once more. If it fails to ignite, then your range repairman will inspect the connections and igniter for any other problem.

How To Repair Gas Stove Igniter

If the burner has been well cleaned and other gas stove repair has been done and the igniter still won’t light, then it could the one causing the problem. Your range repairman will ignite the stove with the lights off to test it. An orange or yellow spark as opposed to a clean bluish-white spark means that the igniter needs to be replaced.

To remove the faulty igniter, power and gas are shut off and then the burner base is screwed out. All wires leading from the igniter will also be disconnected to have it removed. Your repairman will use your stove’s model number as a guide in buying a new igniter. The new igniter, burner base, cap and the stove’s grate will then be replaced. Next, power and gas are restored before the new burner is tested.

Stove Not Working – Loose Connections

Though not common, some connections of your gas range or stove may become loose probably due to cleaning or installation. Loose wires that link the igniter to the stoves control module may affect ignition.

You can invite an oven technician to your home to inspect for any loose connections. First, power is switched off. Next grate, burner cap and sealed burner base are removed to inspect for any loose wires. Loose or disconnected wires are then secured in place. Finally, burner base, cap and grate are reinstalled before power is switched on to test the new connection.

A gas range will always be useful for every household and with proper care, you can continue enjoying its advantages. In terms of energy costs, a gas stove can be very saving since it continues cooking even when the power is not on. The stove also provides instant heat which saves your cooking time. Consider hiring a stove service technician to provide maintenance service for your gas range and prolong its life.

The following are things you should be familiar with when solving the problem with your home appliance or gas stove igniter not clicking

  • gas burners
  • burner knobs
  • surface burners
  • burner caps
  • burner holes
  • control module
  • ignition burners
  • sealed burners
  • igniter switch
  • burner grates
  • ranges burner
  • electronic igniter
  • top igniter
  • oven door
  • wire connector
  • burner heads
  • igniter module
  • igniter sparks
  • spark ignition
  • spark module
  • stove burner
  • burner igniter
  • oven igniter
  • gas cooktop
  • spark ignition switch
  • igniter control module
  • range top
  • gas stove top
  • stove repair

Common causes and problems your are likely to identify with your gas appliance

  • gas stove igniter won’t click
  • disconnected wire
  • gas leak
  • wont heat
  • wont ignite
  • won’t stop clicking
  • clicking sound
  • igniter wont stop
  • continuous clicking
  • igniter clicking
  • burners wont light
  • stop clicking
  • oven wont work
  • stove top not working
  • burner won’t work
  • ignites the gas
  • wrong oven temperature
  • electric range won’t work
  • gas ovens won’t work

Possible Solutions

  • clean the burner
  • replace the igniter
  • remove the grate
  • remove the burner
  • door repair

List of Broward County Locations We Serve:

Gas Stove Repair Pompano Beach Florida, Stove Technician, Dania, Margate, Miramar, Tamarac, Lauderdale Lakes, Parkland, Refrigerator Repair, Gas Appliance Repair, Range Repair, Oven Repair Technician in Oakland Park, Lauderhill, Fort Lauderdale, Appliance Repair Service in Cooper City FL, Plantation, Sunrise FL Microwave Repair, Hallandale, Stove Repair, Deerfield Beach, Davie, Pembroke Pines FL In Home Appliance Repair

If you are having problems with your gas hob not lighting or not staying lit, this article is for you.

A gas hob isn’t too complicated of a thing. In fact, a gas hob only has three basic elements to it.

However, it’s still tricky to figure out why your gas hob isn’t staying lit sometimes. So, let’s explore gas hobs, a few problems that can occur with them and the solutions.

Components of a Gas Hob

Just before some causes and solutions, let’s explore the components of a gas hob. A gas hob has three basic elements, as we said. These are:

  • Gas burner assembly
  • Ignition system
  • Safety system

For the purposes of this gas hob article, we’re going to assume that the gas hob is lighting but then going out. So, the two basic elements of the hob that we need to focus on are the burner assembly and the safety system.

Cause #1: Thermocouple problems

A thermocouple is basically the safety system of your gas hob. It is a piece of pipe situated in the flame of the burner.

When the flame is turned on, this piece of pipe (which is filled with gas) heats up and expands. This basically tells the gas valve that there is still a flame and that it should still be delivering gas to the burner.

So, when you turn your gas burner on and have to hold it for a few seconds, these few seconds are what heat the thermocouple up. The problem with thermocouples can come when they are situated in the flame incorrectly or is the thermocouple is faulty.

Gas

Some people have noticed that thermocouples can become loose over time too, so it’s worth checking yours.

If your thermocouple is faulty or not sitting in the flame correctly, there isn’t a way of cobbling together a solution. A thermocouple is a safety feature that cannot be bypassed.

So, the solution to any thermocouple problems is to check its positioning, if that’s fine, it is likely faulty, and a replacement is needed.

Cause #2: Poor flame or blocked jets

Problems with gas hobs can be caused by a poor flame. What happens here is that the flame cannot reach the thermocouple or not provide enough heat for the thermocouple to keep the gas valve open. This likely means that the burner is blocked or dirty.

The solution for a poor flame or blocked jets is cleaning. Cleaning a gas hob is pretty simple. You can remove the large part of a gas burner and ensure that all of the little holes are clean.

When you lift off the burner, you should see a small brass nut with a small hole in it. That is the gas jet, if that is blocked, you can try using a piece of wire to free anything blocking the jet.

Miele Gas Cooktop Igniter Problems Chart

Conclusion

These are the most common reasons a gas hob may light up and then go out.

Miele Gas Cooktop Igniter Problems Pictures

Now, a word of warning. If you intend to replace any parts of your gas hob, you must make sure that they are the correct parts for your hob. Also, if you’re not sure about something, stop.

Trying to fix a gas hob by yourself can be extremely dangerous. It is best to get a gas engineer out if you can’t find a simple solution to your gas hob issues.

We hope this look at gas hobs and their lighting issues has been helpful. For more information about cookers and hobs, please explore our website further. We have loads of cooker articles on here that can help you choose, maintain and cook with your hob!

Miele Gas Cooktop Ignition Problems

Scott is a writer and a passionate home chef. His passion for cooking began when he was 10 years old. Scott has been writing professionally for over five years now and loves to combine his passion for cooking with his day job.

Miele Gas Cooktop Igniter Problems

Related Posts: